USB BAM driver to support BAM-to-BAM
USB<->Peripheral transactions.
Change-Id: Ib49a41f5dcdccb6f6bff2492fa64ead40f18b870
Signed-off-by: Ofir Cohen <ofirc@codeaurora.org>
When USB cable is connected, the mass storage function in the
device will get interrupts for every 3ms. Entering and exiting the
idle standalone PC itself will take around 3ms on 8960. Hence allowing
idle standalone PC when USB cable is connected causes processor to
spend most of the time in entering and exiting the idle standalone PC.
Hence Vote for minimum DMA latency to prevent idle standalone PC
when USB cable is connected.
Change-Id: Id625dc01f253ed553b2f65f08900022a8c6e1daa
Signed-off-by: Anji jonnala <anjir@codeaurora.org>
USB PHY takes TCXO clock as input and using the PHY internal PLL,
gets the 480MHz clock for USB operations. While USB PHY is suspended,
the TCXO clock can be turned off.
On 8960 target, mandating that TCXO clock users must need to vote for
TCXO and if all the users vote for TCXO clock-off, then MSM can switch to
lower power clock and can run.
Change-Id: Ia9a91bca52a1003439a3a38bbd8eb835dbf349e1
Signed-off-by: Anji jonnala <anjir@codeaurora.org>
Signed-off-by: Matt Wagantall <mattw@codeaurora.org>
This USB CCID function driver will be a transport layer between
userspace CCID component and the Windows Host. Data and control
commands from the Windows Host will be sent to the userspace component
and vice-versa.
Change-Id: I5f00f9802a57329d2c932bba740b286b98cb8e27
Signed-off-by: Chiranjeevi Velempati <cvelempa@codeaurora.org>
Current implementation supports PHY retention mode, when
VBUS detection is done by PMIC.
This change adds the support for PHY retention mode, for
the case where VBUS detection is done by USB PHY.
In that case, the PHY wakes up the MPM and CORE using its
High-Voltage interrupts.
Change-Id: I5fec518337413f175a8bc671897836affc55381c
Signed-off-by: Amit Blay <ablay@codeaurora.org>
* common/android-3.0: (570 commits)
misc: remove kernel debugger core
ARM: common: fiq_debugger: dump sysrq directly to console if enabled
ARM: common: fiq_debugger: add irq context debug functions
net: wireless: bcmdhd: Call init_ioctl() only if was started properly for WEXT
net: wireless: bcmdhd: Call init_ioctl() only if was started properly
net: wireless: bcmdhd: Fix possible memory leak in escan/iscan
cpufreq: interactive governor: default 20ms timer
cpufreq: interactive governor: go to intermediate hi speed before max
cpufreq: interactive governor: scale to max only if at min speed
cpufreq: interactive governor: apply intermediate load on current speed
ARM: idle: update idle ticks before call idle end notifier
input: gpio_input: don't print debounce message unless flag is set
net: wireless: bcm4329: Skip dhd_bus_stop() if bus is already down
net: wireless: bcmdhd: Skip dhd_bus_stop() if bus is already down
net: wireless: bcmdhd: Improve suspend/resume processing
net: wireless: bcmdhd: Check if FW is Ok for internal FW call
tcp: Don't nuke connections for the wrong protocol
ARM: common: fiq_debugger: make uart irq be no_suspend
net: wireless: Skip connect warning for CONFIG_CFG80211_ALLOW_RECONNECT
mm: avoid livelock on !__GFP_FS allocations
...
Conflicts:
arch/arm/mm/cache-l2x0.c
arch/arm/vfp/vfpmodule.c
drivers/mmc/core/host.c
kernel/power/wakelock.c
net/bluetooth/hci_event.c
Signed-off-by: Bryan Huntsman <bryanh@codeaurora.org>
Add device tree support for MSM HSUSB. The OTG driver registers
gadget and host platform devices based on the operational mode.
This patch also updates the copper device tree source file with
HSUSB device specifics.
Change-Id: I0a50b0500d15f32ff65468cdb411398a80a20329
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Synopsis 28nm PHY has two different circuits for detecting changes on
ID line. ID_DIG is designed for detecting ID_float vs ID_gnd. ID_ACA
is designed for detecting RID_A, RID_B, RID_C states. These are mutually
exclusive and enabling both circuits has undefined behavior. Enable
ID_ACA upon VBUS high or ID_gnd events to detect further ACA states.
ACA ID_GND threshold range is overlapped with OTG ID_FLOAT threshold range.
Hence PHY ID_DIG circuit can not be used for detecting ACA ID_GND. Use
PMIC ID circuit for detecting both OTG and ACA ID_GND.
Link controller can not generate PHY_ALT interrupt in host mode. But the
corresponding PHY register reflects the actual ID state. Hence implement
polling to read PHY register to detect ID_GND --> ID_A, ID_A --> ID_B
transitions. That means low power mode can not be allowed in host mode.
Also disallow suspending the device attached on the root hub. Otherwise
PHY is put into suspend state automatically upon setting SUSP bit in PORTSC
register.
Link controller can not generate asynchronous interrupt for ID_ACA changes
in low power mode. Hence disallow low power mode in ID_B and ID_C states.
USB_MSM_ACA is not selected by default. If it selected, ACA states can be
detected and low power mode is not allowed in host mode. Writing "enable"
to <debugfs>/msm_otg/aca enables ACA irrespective of USB_MSM_ACA selection.
This is meant for debugging only.
Change-Id: I51e80d803a583c5bdffc8111696943c04958f604
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
In case of 8960 Liquid, need to vote for EXT_3P3V regulator
to avoid usb connection lost as MHL analog switch is powered
by this regulator.
Change-Id: Ifc36d7916a5407801fdf43357176efa264d160bd
CRs-fixed: 315979
Signed-off-by: Vijayavardhan Vennapusa <vvreddy@codeaurora.org>
SMSC hub must be configured so that Conventional USB
devices can be connected to SMSC hub on 8960 liquid.
Change-Id: I261798de153d3c37f2fa2c4d7e15d96bb81c432f
Signed-off-by: Vijayavardhan Vennapusa <vvreddy@codeaurora.org>
OTG drivers that use USB core functions like usb_add_hcd, usb_remove_hcd,
etc can be selected for gadget only mode without selecting CONFIG_USB.
Change-Id: Ie4b0c1703622cc9051ad9f50b8901f0005daeeb6
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
As part of HSIC initialization, in addition to enabling HSIC host
mode and periodic pad calibration, need to configure GPIO150 and
GPIO151 pins for HSIC strobe and data lines respectively for
proper data communication between HSIC devices.
Change-Id: I7cdf8e4532045d813ac6c6e3f53455d0a640245b
Signed-off-by: Vijayavardhan Vennapusa <vvreddy@codeaurora.org>
This patch adds support for EHCI compliant USB Host Controller
present in MSM chips. This Controller uses an HSIC PHY which
communicates with downstream devices using STROBE/DATA lines.
HSIC is a supplement to USB 2.0 specification and is preferred
for chip-to-chip interconnect (having maximum circuit length of
10cm) as it removes the analog transceivers.
Change-Id: Id54dcc802e606e0ff7dd31bc64671a797cd8bc09
Signed-off-by: Vijayavardhan Vennapusa <vvreddy@codeaurora.org>
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
This change add usb system clock support to OTG Driver.
System clock is a 60MHZ input clock to the USB ChipIdea core.
This clock is required starting from MDM9615.
This change also removes the enforcement for using a phy_reset_clk
for reseting the PHY. Starting from MDM9615, PHY reset is not implemented.
The core is reset together with the PHY using "usb_hs_clk" signal.
Signed-off-by: Amit Blay <ablay@codeaurora.org>
It is possible that while one driver has already suspended,
another driver calls otg_id_notify() because it has not yet been
suspended. It would then be possible for the suspended driver's
detect callback to be called. This is undesirable.
Introduce new otg_id_suspend/otg_id_resume functions that
keep a suspended count, and if a notification happens while
someone is suspended, that notification is deferred until
all the drivers are resumed. If the notification happens before
the last driver is suspended, that suspend will be aborted
and once the final driver resumes through otg_id_resume, the
notification will be delivered.
Change-Id: I32fd32bec65e366e5f97a25c15255d94773b85b3
Signed-off-by: Dima Zavin <dima@android.com>
Some otg_id handlers can detect what's connected but can't detect a change.
This allows that handler to pass off the waiting for ID change to a proxy.
Change-Id: Ib38b750c3da4bffc35e37b620ecee37c5d64d31f
Signed-off-by: Erik Gilling <konkers@android.com>
MTP_SEND_FILE_WITH_HEADER ioctl allows sending a file with the 12 byte header
prepended at the beginning.
This is to allow MTP to use a single packet for the data phase instead of two.
Signed-off-by: Mike Lockwood <lockwood@android.com>
Add a otg_id notifier to allow multiple drivers to cooperate to
determine the type of cable connected to a USB connector without
requiring direct calls between the drivers.
Change-Id: Ic5675f1a89daf85b17336765de24e4bdb6df6348
Signed-off-by: Colin Cross <ccross@android.com>
This is the same as MTP but with PTP interface descriptor.
Also removed obsolete ioctl for switching between MTP and PTP mode
Signed-off-by: Mike Lockwood <lockwood@android.com>
* Functions and the device descriptor are configured from user space:
echo 0 > /sys/class/android_usb/android0/enable
echo adb,acm > /sys/class/android_usb/android0/functions
echo 2 > /sys/class/android_usb/android0/f_acm/instances
echo 1 > /sys/class/android_usb/android0/enable
* Driver does not require platform data anymore
* Moved function initialization to android.c instead of each
function file
* Replaced switches by uevents
Signed-off-by: Benoit Goby <benoit@android.com>
Signed-off-by: Mike Lockwood <lockwood@android.com>
Change-Id: If5ad9267c111ad0a442f0d87a0d31082dc5381b6
This allows composite drivers to dynamically change their configuration.
For example, a driver might remove a configuration and register a new
one with a different set of functions.
User should prevent the host from enumerating the device while changing
the configuration:
usb_gadget_disconnect(cdev->gadget);
usb_remove_config(cdev, old_config);
usb_add_config(cdev, new_config, new_conf_bind);
usb_gadget_connect(cdev->gadget);
Change-Id: Icbfb4ce41685fde9bf63d5d58fca1ad242aa69f9
Signed-off-by: Benoit Goby <benoit@android.com>
Signed-off-by: Mike Lockwood <lockwood@android.com>
USB: gadget: f_accessory: Misc improvements and cleanup:
- Add URI string
- Replace type string with a description string
- Add a control call to retrieve accessory protocol version (currently 1)
- Driver read() and write() calls now fail after USB disconnect until
driver file is closed and reopened.
- Misc cleanup work
Signed-off-by: Mike Lockwood <lockwood@android.com>
USB: gadget: f_accessory: Clear accessory strings when USB is disconnected
Signed-off-by: Mike Lockwood <lockwood@android.com>
USB: gadget: f_accessory: Clear previous strings on ACCESSORY_GET_PROTOCOL
Clearing strings on disconnect does not work since we may receive
a disconnect on some devices when transitioning into accessory mode.
We require an accessory to send ACCESSORY_GET_PROTOCOL before
sending any strings, so any strings from a previous session will be cleared.
Signed-off-by: Mike Lockwood <lockwood@android.com>
USB: gadget: f_accessory: Clear disconnected flag when driver file is opened
Fixes a race condition that can occur when entering accessory mode.
Signed-off-by: Mike Lockwood <lockwood@android.com>
USB: gadget: f_accessory: Add string for accessory's unique serial number
Signed-off-by: Mike Lockwood <lockwood@android.com>
USB: gadget: f_accessory: Set bNumEndpoints to correct value of 2
Change-Id: I24f4e36f196d45436e0573301500c3b93215953d
Signed-off-by: Mike Lockwood <lockwood@android.com>
Based on the list of enabled USB functions, we can now switch the vendor ID
as well as the product ID.
Signed-off-by: Mike Lockwood <lockwood@android.com>
- Added multiple ACM instance support in Android gadget
- Fixed multiple instance naming issue in ACM function
- Increased max instances from 4 to 8
Change-Id: I65f1b0be94da859bab7ec0ad7cd804b896c7c4c5
Signed-off-by: John Michelau <john.michelau@motorola.com>
For backward compatibility with PTP, MTP is limited to a 32-bit file size.
When transferring files greater than 4 gig, MTP uses 0xFFFFFFFF as the file size
and the receiver reads until it receives a short packet.
Expanded size of mtp_file_range.length to 64 bits and added support for
writing zero length packets.
Signed-off-by: Mike Lockwood <lockwood@android.com>
Use this rather than calling usb_gadget_disconnect and usb_gadget_connect
directly to avoid sending USB disconnect events to userspace when resetting
the bus.
Signed-off-by: Mike Lockwood <lockwood@android.com>
Add switch to notify current USB configuration. This can be used to detect
USB connect and disconnect events.
Broadcast a change via the usb_composite class when a USB function is
enabled or disabled.
Rename usb_function.hidden to usb_function.disabled.
Signed-off-by: Mike Lockwood <lockwood@android.com>
USB: android gadget: add remote wakeup attribute to android function
Add remote wakeup attribute to configuration descriptor of android
function to advertise remote wakeup capability to host
Acked-by: Allam, Suresh Reddy <sallam@qualcomm.com>
Signed-off-by: Mike Lockwood <lockwood@android.com>
USB: gadget: android: Allow functions to handle setup requests.
Signed-off-by: Mike Lockwood <lockwood@android.com>
Support for specifying the list of USB functions from platform data.
The main android.c gadget driver no longer has hard coded references
to the mass_storage and adb functions.
Support for computing the product ID based on tables in platform data
and the currently enabled functions.
Moved the adb enable/disable logic from android.c to f_adb.c.
Change-Id: I6259d3fb1473ed973f700e55d17744956f3527bb
Signed-off-by: Mike Lockwood <lockwood@android.com>
Change-Id: I4101540916b73a5f4e48684727ff782f98b969c7
Signed-off-by: Mike Lockwood <lockwood@android.com>
USB: android gadget: add remote wakeup attribute to android function
Add remote wakeup attribute to configuration descriptor of android
function to advertise remote wakeup capability to host
Acked-by: Allam, Suresh Reddy <sallam@qualcomm.com>
Signed-off-by: Mike Lockwood <lockwood@android.com>
usb gadget: link fixes for android composite gadget
Signed-off-by: Mike Lockwood <lockwood@android.com>
usb gadget: Fix null pointer errors in android composite driver
Signed-off-by: Mike Lockwood <lockwood@android.com>
usb: gadget: android: Allow usb charging to draw up to 500mA instead of 250.
Signed-off-by: Rebecca Schultz Zavin <rebecca@android.com>
usb gadget: android: Add helper function for usb_gadget_connect and disconnect.
Signed-off-by: Mike Lockwood <lockwood@android.com>
drivers: usb: gadget: call switch_dev_unregister in mass storage unbind callback
This fixes a problem unloading the android gadget driver when built as a module
Signed-off-by: Mike Lockwood <lockwood@android.com>
usb: gadget: android: Add dependency on switch driver.
Signed-off-by: Mike Lockwood <lockwood@android.com>
USB: gadget: android: Fix USB WHQL Certification Issues
Submitted on behalf of RaviKumar Vembu <ravi.v@motorola.com>
Signed-off-by: Jared Suttles <jared.suttles@motorola.com>
Signed-off-by: Mike Lockwood <lockwood@android.com>
drivers: usb: gadget: Add "usb_mass_storage" platform driver.
This will be used for configuring vendor, product and release from board file.
Submitted on behalf of RaviKumar Vembu <ravi.v@motorola.com>
Signed-off-by: Jared Suttles <jared.suttles@motorola.com>
Signed-off-by: Mike Lockwood <lockwood@android.com>
drivers: usb: gadget: Use usb_mass_storage platform device as parent for lun
If a platform device is specified for the f_mass_storage function, use it as the
parent driver for the lun files in sysfs.
This allows a platform independent file path for controlling USB mass storage
from user space.
Signed-off-by: Mike Lockwood <lockwood@android.com>
drivers: usb: gadget: Add platform data struct for usb_mass_storage device
Signed-off-by: Mike Lockwood <lockwood@android.com>
usb: gadget: mass_storage: Fix Mass Storage Panic during PC reboot
Submitted on behalf of RaviKumar Vembu <ravi.v@motorola.com>
Signed-off-by: Jared Suttles <jared.suttles@motorola.com>
Signed-off-by: Mike Lockwood <lockwood@android.com>
usb: gadget: f_mass_storage: Handle setup request correctly
Signed-off-by: Mike Lockwood <lockwood@android.com>
usb: gadget: f_mass_storage: Clean up wakelocks on error paths
Signed-off-by: Rebecca Schultz Zavin <rebecca@android.com>
Signed-off-by: Mike Lockwood <lockwood@android.com>
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (205 commits)
USB: EHCI: Remove SPARC_LEON {read,write}_be definitions from ehci.h
USB: UHCI: Support big endian GRUSBHC HC
sparc: add {read,write}*_be routines
USB: UHCI: Add support for big endian descriptors
USB: UHCI: Use ACCESS_ONCE rather than using a full compiler barrier
USB: UHCI: Add support for big endian mmio
usb-storage: Correct adjust_quirks to include latest flags
usb/isp1760: Fix possible unlink problems
usb/isp1760: Move function isp1760_endpoint_disable() within file.
USB: remove remaining usages of hcd->state from usbcore and fix regression
usb: musb: ux500: add configuration and build options for ux500 dma
usb: musb: ux500: add dma glue layer for ux500
usb: musb: ux500: add dma name for ux500
usb: musb: ux500: add ux500 specific code for gadget side
usb: musb: fix compile error
usb-storage: fix up the unusual_realtek device list
USB: gadget: f_audio: Fix invalid dereference of initdata
EHCI: don't rescan interrupt QHs needlessly
OHCI: fix regression caused by nVidia shutdown workaround
USB: OTG: msm: Free VCCCX regulator even if we can't set the voltage
...
Some USB function drivers (e.g. f_mass_storage.c) need to delay or defer the
data/status stages of standard control requests like SET_CONFIGURATION or
SET_INTERFACE till they are done with their bookkeeping and are actually ready
for accepting new commands to their interface.
They can now achieve this functionality by returning USB_GADGET_DELAYED_STATUS
in their setup handlers (e.g. set_alt()). The composite framework will then
defer completion of the control transfer by not completing the data/status stages.
This ensures that the host does not send new packets to the interface till the
function driver is ready to take them.
When the function driver that requested for USB_GADGET_DELAYED_STATUS is done
with its bookkeeping, it should signal the composite framework to continue with
the data/status stages of the control transfer. It can do so by invoking
the new API usb_composite_setup_continue(). This is where the control transfer's
data/status stages are completed and host can initiate new transfers.
The DELAYED_STATUS mechanism is currently only supported if the expected data phase
is 0 bytes (i.e. w_length == 0). Since SET_CONFIGURATION and SET_INTERFACE are the
only cases that will use this mechanism, this is not a limitation.
Signed-off-by: Roger Quadros <roger.quadros@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Implement good battery algorithm defined in the battery charging V1.2 spec
for detecting different charging ports. USB hardware is put into low power
mode when connected to a dedicated charging port. vbus_draw and set_power
methods are implemented for determining the allowed current from Host in
different states (un-configured/suspend/configured).
The charger block is implemented using vendor specific registers and the
PHY used in MSM8960(28nm PHY) different from older targets like MSM8x60
and MSM7x30(45nm PHY). The PHY vendor and product id registers are not
implemented in the above chipsets. Hence PHY type is passed via platform
data.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
HSUSB core clock is derived from daytona fabric clock and for
HSUSB operational require minimum core clock at 55MHz. Since, HSUSB
cannot tolerate daytona fabric clock change in the middle of HSUSB
operational, vote for maximum Daytona fabric clock
while usb is operational
Signed-off-by: Anji jonnala <anjir@codeaurora.org>
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 3dacdf11 "usb: factor out state_string() on otg drivers"
broke building musb drivers since there is already another
otg_state_string() function in musb drivers, but with different
prototype. Fix musb drivers to use common otg_state_string(), too.
Also provide a nop for otg_state_string() if CONFIG_USB_OTG_UTILS
is not defined.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The two first HC capability registers (CAPLENGTH and HCIVERSION)
are defined as one 8-bit and one 16-bit register. Most HC
implementations have selected to treat these registers as part
of a 32-bit register, giving the same layout for both big and
small endian systems.
This patch adds a new quirk, big_endian_capbase, to support
controllers with big endian register interfaces that treat
HCIVERSION and CAPLENGTH as individual registers.
Signed-off-by: Jan Andersson <jan@gaisler.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As pointed out by Arnd Bergmann, in include/linux/usb/ehci_def.h, struct
ehci_caps is defined with __attribute__((packed)) for no good reason,
and this triggers undefined behaviour when using ARM's readl() on
pointers to elements of this structure:
http://lkml.kernel.org/r/201102021700.20683.arnd@arndb.de
The same problem exists with the other two structures in ehci_def.h too,
so remove the __attribute__((packed)) from all of them.
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-usb-next' of git+ssh://master.kernel.org/pub/scm/linux/kernel/git/sarah/xhci:
xhci 1.0: Set transfer burst last packet count field.
xhci 1.0: Set transfer burst count field.
xhci 1.0: Update TD size field format.
xhci 1.0: Only interrupt on short packet for IN EPs.
xhci: Remove sparse warning about cmd_status.
usbcore: warm reset USB3 port in SS.Inactive state
usbcore: Refine USB3.0 device suspend and resume
xHCI: report USB3.0 portstatus comply with USB3.0 specification
xHCI: Set link state support
xHCI: Clear link state change support
xHCI: warm reset support
usb/ch9: use proper endianess for wBytesPerInterval
xhci: Remove recursive call to xhci_handle_event
xhci: Add an assertion to check for virt_dev=0 bug.
xhci: Add rmb() between reading event validity & event data access.
xhci: Make xHCI driver endian-safe
