Add a resource managed regulator_get() to simplify regulator
usage in drivers. This allows driver authors to "get and forget"
about their regulators by automatically calling regulator_put()
when the driver is detached.
[Fixed up a couple of coding style issues -- broonie]
Change-Id: Ie32415c3a9f2c4aa99a98b6cb92a784e23d874ea
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Delete the pm8018-regulator driver now that it has been replaced
by the pm8xxx-regulator driver.
Change-Id: I18b4944dcea6ef6900f740b61621548bd1ac9d49
Signed-off-by: David Collins <collinsd@codeaurora.org>
Delete the pm8921-regulator driver now that it has been replaced
by the pm8xxx-regulator driver.
Change-Id: I36ab68ae7b37988356397d4ac5039aa78a1a2955
Signed-off-by: David Collins <collinsd@codeaurora.org>
Create a PM8XXX regulator driver that can support PMIC PM8921
variants including: PM8018, PM8038, and PM8921.
Change-Id: I60d1302e4af9a4c5caa72301c904867acd2ebe0f
Signed-off-by: David Collins <collinsd@codeaurora.org>
Move the following subdevices to use the pm8xxx interface -
mpp, irq, thermal, regulators.
This allows usage of a common driver for modules which are same
across multiple PM8XXX PMICs. It also provides flexibility
to add/remove subdevices for multiple board configurations.
Change-Id: I6478ec1b99b1ab55ca370d314dbeb590103a4b1c
Signed-off-by: Anirudh Ghayal <aghayal@codeaurora.org>
The low power mode select bit is located at bit 2 of bank 0 of the
LDO TEST register. Correct the mask used in the pm8921-regulator
driver to reflect this.
Change-Id: Id5b127ed2894791444f4dcd0ac7dfaed516f5f12
Signed-off-by: David Collins <collinsd@codeaurora.org>
* common/android-3.0: (570 commits)
misc: remove kernel debugger core
ARM: common: fiq_debugger: dump sysrq directly to console if enabled
ARM: common: fiq_debugger: add irq context debug functions
net: wireless: bcmdhd: Call init_ioctl() only if was started properly for WEXT
net: wireless: bcmdhd: Call init_ioctl() only if was started properly
net: wireless: bcmdhd: Fix possible memory leak in escan/iscan
cpufreq: interactive governor: default 20ms timer
cpufreq: interactive governor: go to intermediate hi speed before max
cpufreq: interactive governor: scale to max only if at min speed
cpufreq: interactive governor: apply intermediate load on current speed
ARM: idle: update idle ticks before call idle end notifier
input: gpio_input: don't print debounce message unless flag is set
net: wireless: bcm4329: Skip dhd_bus_stop() if bus is already down
net: wireless: bcmdhd: Skip dhd_bus_stop() if bus is already down
net: wireless: bcmdhd: Improve suspend/resume processing
net: wireless: bcmdhd: Check if FW is Ok for internal FW call
tcp: Don't nuke connections for the wrong protocol
ARM: common: fiq_debugger: make uart irq be no_suspend
net: wireless: Skip connect warning for CONFIG_CFG80211_ALLOW_RECONNECT
mm: avoid livelock on !__GFP_FS allocations
...
Conflicts:
arch/arm/mm/cache-l2x0.c
arch/arm/vfp/vfpmodule.c
drivers/mmc/core/host.c
kernel/power/wakelock.c
net/bluetooth/hci_event.c
Signed-off-by: Bryan Huntsman <bryanh@codeaurora.org>
Move the following subdevices to use the pm8xxx interface -
mpp, irq, gpio, keypad, power-key, leds, othc, vibrator,
rtc, batt-alarm, thermal, upl, nfc, pwm, xoadc, regulators,
xo-buffers, charger.
This allows usage of a common driver for modules which are same
across multiple PM8XXX PMICs. It also provides flexibility
to add/remove subdevices for multiple board configurations.
Change-Id: Id9795552fc9f4a2c920c070babfaef1f4cd6ca61
Signed-off-by: Anirudh Ghayal <aghayal@codeaurora.org>
The chip pointer now comes from the parent and not
the driver data.
Change-Id: Icb991e74a640ac7d1150a93206733e3e5fc4603d
Signed-off-by: Anirudh Ghayal <aghayal@codeaurora.org>
Create a regulator driver to control all regulators on the Qualcomm
PM8018 PMIC chip. This chip contains several different types of
regulators with a wide range of abilities and voltage ranges.
Five different regulator types are available on the PM8018.
PLDO - PMOS low drop out linear regulator
NLDO - NMOS low drop out linear regulator
NLDO1200 - 1.2A NMOS LDO (different control structure than other LDOs)
SMPS - switched-mode power supply
VS - voltage switch
The driver interfaces with the PMIC using Qualcomm's SSBI bus.
Calls to this bus are abstracted through the pm8xxx_readb/writeb API.
Signed-off-by: David Collins <collinsd@codeaurora.org>
Add a convenience API to set the voltage on multiple consumers
stored in a struct regulator_bulk_data[] in one API call.
Signed-off-by: Justin Paupore <jpaupore@codeaurora.org>
The pull down enable bit of the 100 mA LVS control register was set
the same way as those in LDO and SMPS regulators. I.e. set to 1 to
enable the pull down and set to 0 to disable it. However, the pull
down bit meaning for 100 mA LVS's is inverted. Correct this in the
driver.
Signed-off-by: David Collins <collinsd@codeaurora.org>
commit d04156bca629740a661fd0738cd69ba1f08b2b20 upstream.
Also add a default case in tps65910_list_voltage_dcdc to silence
'volt' may be used uninitialized in this function warning.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
PMIC 8921 regulator LDO 4 should normally be set to 1.8 V. However,
for PMIC revisions 1.1 and below, this voltage is insufficient for
internal PMIC circuitry. This results in some SSBI registers in the
PMIC not reading back properly. Therefore, add a hack which raises
the voltage set for LDO 4 to 2.0 V to fix the issue.
Signed-off-by: David Collins <collinsd@codeaurora.org>
Add an enable_time platform data member which can be used to specify
the board dependent enable (rise) time of each regulator.
Signed-off-by: David Collins <collinsd@codeaurora.org>
The platform_data (pdata) may be pointing to __initdata section, which
may be free'd from the memory. The dependency on pdata in non-init
functions is removed in this patch to allow platform to declare
__initdata for platform data.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
In the case of get_voltage callback is NULL, current implementation in
_regulator_get_voltage will return -EINVAL.
Also returns proper error if ret is negative value.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Adding support for the twl6025. Major difference in the twl6025 is the
group functionality has been removed from the chip so this affects how
regulators are enabled and disabled.
The names of the regulators also changed.
The DCDCs of the 6025 are software controllable as well.
Since V1
Use the features variable passed via platform data instead of calling
global function.
Change the very switch like if statements to be a more readable
switch statement.
Since V2
twl6025 doesn't use remap so remove it from the macros.
Since V3
enable/disable functions for 4030/6030 were seperated upstream so rebase
on top of this. Change DCDC reference to SMPS as this is used in TRM.
Change list_voltage slightly to have less code.
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
TWL6030: regulator is disabled via VREG_STATE
TWL4030: regulator is disabled via VREG_GRP
Since there is nothing common, split twlreg_enable similar to other regulator_ops
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
TWL6030: regulator is enabled via VREG_STATE
TWL4030: regulator is enabled via VREG_GRP
Since there is nothing common, split twlreg_enable similar to other regulator_ops
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The tps65911 chip introduces new features, including changes in
the regulator module.
- VDD1 and VDD2 remain unchanged.
- VDD3 is now named VDDCTRL and has a wider voltage range.
- LDOs are now named LDO1...8 and voltage ranges are sequential,
making LDOs easier to handle.
Signed-off-by: Jorge Eduardo Candelaria <jedu@slimlogic.co.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
In current implementation, the original macro implementation assumes the caller
pass the parameter starting from 1 (to match the register names in datasheet).
Thus we have unneeded plus one then minus one operations
when using MAX8997_REG_BUCK1DVS/MAX8997_REG_BUCK2DVS/MAX8997_REG_BUCK5DVS macros.
This patch removes these macros to avoid unneeded plus one then minus one operations
without reducing readability.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
When applying the set_voltage() requests from consumers skip over those
consumers that haven't set anything, otherwise we'll come out with a
maximum voltage of zero.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
If either a regulator driver can't tell us what the optimum mode is (or
doesn't have modes in the first place) or the system doesn't allow DRMS
changes then it's more helpful for users to just say that we're in the
optimal mode, even if it's from a selection of one.
Still report errors if the process of picking and setting a mode changes as
this may indicate that we're stuck in a low power mode and unable to deliver
a higher current that the consumer just asked for.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The desc_id variable should not be a static variable.
The rest of the code assumes the desc_id must less than TPSxxxxx_NUM_REGULATOR.
If we set desc_id to be a static variable, checking the return value of
rdev_get_id() may return error.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Anuj Aggarwal <anuj.aggarwal@ti.com>
Cc: Graeme Gregory <gg@slimlogic.co.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
I check this patch again and found this actually is not a bug
because MC13xxx_DEFINE explictly defines the order of each entry in the array.
Thus revert the patch.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
These became unused with the IRQ removal patch, I'm fairly sure that a
patch was sent earlier by someone else but it doesn't seem to have been
applied and I don't have a copy sitting around any more.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The regulator module consists of 3 DCDCs and 8 LDOs. The output
voltages are configurable and are meant to supply power to the
main processor and other components
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Jorge Eduardo Candelaria <jedu@slimlogic.co.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Currently, we call mc13xxx_reg_read and mc13xxx_reg_rmw for the same register.
This can be converted to simply a mc13xxx_reg_read and a mc13xxx_reg_write,
thus save a redundant register read.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Some systems, particularly physically large systems used for early
prototyping, may experience substantial voltage drops between the regulator
and the consumers as a result of long traces in the system. With these
systems voltages may need to be set higher than requested in order to
ensure reliable system operation.
Allow systems to work around such hardware issues by allowing constraints
to supply an offset to be applied to any requested and reported voltages.
This is not ideal, especially since the voltage drop may be load dependant,
but is sufficient for most affected systems, it is not expected to be used
in production hardware. The offset is applied after all constraint
processing so constraints should be specified in terms of consumer values
not physically configured values.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
supply_regulator_dev (using a struct pointer) has been deprecated in favour
of supply_regulator (using a regulator name) for quite a few releases
now with a warning generated if it is used and there are no current in tree
users so just remove the code.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
In include/linux/mfd/mc13892.h, we define MC13892_VCOINCELL as 23.
Thus VCOINCELL should be defined as 23th element in mc13892_regulators array, not the first one.
This actually fixes an off-by-one bug while accessing mc13892_regulators array.
For example,
In mc13892_regulator_probe, we use MC13892_VCAM as array index of mc13892_regulators array.
mc13892_regulators[MC13892_VCAM].desc.ops->set_mode
= mc13892_vcam_set_mode;
Currently, it access mc13892_regulators[12] ,which is VAUDIO not VCAM.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The second parameter of regulator_mode_constrain takes a pointer.
This patch fixes below warning:
drivers/regulator/core.c: In function 'regulator_set_mode':
drivers/regulator/core.c:2014: warning: passing argument 2 of 'regulator_mode_constrain' makes pointer from integer without a cast
drivers/regulator/core.c:200: note: expected 'int *' but argument is of type 'unsigned int'
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@vega.(none)>
Current set_mode logic does not support 6030. The logic for 4030 is
not reusable for 6030 as the mode setting for 6030 now uses the new
CFG_STATE register. We hence rename the old get_status as being
specific to 4030.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Saquib Herman <saquib@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@vega.(none)>
Current get_status logic does not support 6030 get_status.
The logic for 4030 is not reusable for 6030 as the status
check for 6030 now depends on the new CFG_STATE register.
We hence rename the old get_status as being specific to
4030 and remove the redundant check for the same.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Saquib Herman <saquib@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@vega.(none)>
With TWL6030, it is not enough to ensure that the regulator is the
group of P1 group (CPU/Linux), but we need to check the state as far
as APP is concerned as well.
Split the current is_enabled to 6030 and 4030 specific ones. This
split impacts few macros and variables as well, but sets up the
stage for further fixes to set_mode and get_status in subsequent
patches.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Saquib Herman <saquib@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@vega.(none)>
TWL6030 does not have remap register. The current implementation
causes value of remap to be written to state register, accidentally
causing the regulators which are probed to be switched on as well.
This is wrong as regulators should be controllable based on calls
to enable/disable for TWL regulator framework. Further, the values
initialized make no sense as well. We hence remove this from the
initalizers and also write to remap register only if the TWL
is 4030.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Saquib Herman <saquib@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@vega.(none)>
TWL6030 requires an additional register write to CFG_STATE register
to explicitly state that the regulator is in a certain state. Merely
associating the regulator with the group is not enough. Add the
required register field definitions and fix the handling for
TWL6030 enable/disable.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Saquib Herman <saquib@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@vega.(none)>
