This patch changes OTG driver to support different
OTG statemachine states for OTG2.0 complaince. It will
also enable to swap Host role between two OTG devices
via HNP and enable B device to request A device to start
VBUS session via SRP.
Change-Id: Ibe2519ff1570768f51e879af483a6f5c23b38d8f
Signed-off-by: Vijayavardhan Vennapusa <vvreddy@codeaurora.org>
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Current implementation supports PHY retention mode, when
VBUS detection is done by PMIC.
This change adds the support for PHY retention mode, for
the case where VBUS detection is done by USB PHY.
In that case, the PHY wakes up the MPM and CORE using its
High-Voltage interrupts.
Change-Id: I5fec518337413f175a8bc671897836affc55381c
Signed-off-by: Amit Blay <ablay@codeaurora.org>
Synopsis 28nm PHY has two different circuits for detecting changes on
ID line. ID_DIG is designed for detecting ID_float vs ID_gnd. ID_ACA
is designed for detecting RID_A, RID_B, RID_C states. These are mutually
exclusive and enabling both circuits has undefined behavior. Enable
ID_ACA upon VBUS high or ID_gnd events to detect further ACA states.
ACA ID_GND threshold range is overlapped with OTG ID_FLOAT threshold range.
Hence PHY ID_DIG circuit can not be used for detecting ACA ID_GND. Use
PMIC ID circuit for detecting both OTG and ACA ID_GND.
Link controller can not generate PHY_ALT interrupt in host mode. But the
corresponding PHY register reflects the actual ID state. Hence implement
polling to read PHY register to detect ID_GND --> ID_A, ID_A --> ID_B
transitions. That means low power mode can not be allowed in host mode.
Also disallow suspending the device attached on the root hub. Otherwise
PHY is put into suspend state automatically upon setting SUSP bit in PORTSC
register.
Link controller can not generate asynchronous interrupt for ID_ACA changes
in low power mode. Hence disallow low power mode in ID_B and ID_C states.
USB_MSM_ACA is not selected by default. If it selected, ACA states can be
detected and low power mode is not allowed in host mode. Writing "enable"
to <debugfs>/msm_otg/aca enables ACA irrespective of USB_MSM_ACA selection.
This is meant for debugging only.
Change-Id: I51e80d803a583c5bdffc8111696943c04958f604
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
This patch adds support for EHCI compliant USB Host Controller
present in MSM chips. This Controller uses an HSIC PHY which
communicates with downstream devices using STROBE/DATA lines.
HSIC is a supplement to USB 2.0 specification and is preferred
for chip-to-chip interconnect (having maximum circuit length of
10cm) as it removes the analog transceivers.
Change-Id: Id54dcc802e606e0ff7dd31bc64671a797cd8bc09
Signed-off-by: Vijayavardhan Vennapusa <vvreddy@codeaurora.org>
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
This patch fixes the below compilation errors.
CC drivers/usb/gadget/ci13xxx_msm.o
CC net/mac80211/led.o
drivers/usb/gadget/ci13xxx_msm.c: In function 'ci13xxx_msm_notify_event':
drivers/usb/gadget/ci13xxx_msm.c:42: error: 'USB_AHBBURST' undeclared (first use in this function)
drivers/usb/gadget/ci13xxx_msm.c:42: error: (Each undeclared identifier is reported only once
drivers/usb/gadget/ci13xxx_msm.c:42: error: for each function it appears in.)
drivers/usb/gadget/ci13xxx_msm.c:43: error: 'USB_AHBMODE' undeclared (first use in this function)
make[4]: *** [drivers/usb/gadget/ci13xxx_msm.o] Error 1
make[3]: *** [drivers/usb/gadget] Error 2
MSM USB driver is not supported on boards like trout (MSM7201) which
has an external PHY.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Implement runtime and system pm ops to put hardware into low power
mode (LPM). As part of LPM, USB clocks are turned off, PHY is put
into suspend state and PHY comparators are turned off if VBUS/Id
notifications are not required from PHY.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver implements PHY initialization, clock management, ULPI IO ops
and simple OTG state machine to kick host/peripheral based on Id/VBUS
line status. VBUS/Id lines are tied to a reference voltage on some boards.
Hence provide debugfs interface to select host/peripheral mode.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
